Sun Microsystems CP3220 Manual de usuario Pagina 49
- Pagina / 135
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2 Hardware Installation and Service 2-15
■ A telnet utility (Connect to the proper port on a Network Terminal Server to
which the Sun Netra CP3220 is connected.)
■ Another suitable serial communications program on the system console
For example, if you are using a UNIX system as the system console, at the UNIX
prompt in a command tool or shell tool, or serial port A, type:
2.2.4.2 Connecting Cables to the System Console Not Running the
Solaris OS
1. Connect a shielded serial cable to the serial console port on the front panel of
the Sun Netra CP3220 blade server (
FIGURE 2-3) or the Sun Netra CP32x0 ARTM.
2. Connect the other end of the serial cable to the serial port of the system serving
as the system console.
3. Set the serial communications settings to 9600 baud, 8 bit, 1 stop bit, no parity,
and no handshake.
2.2.4.3 Netinstall Boot Device Map
TABLE 2-2 provides a map of netinstall boot devices. You may need this information
to understand which MAC address is associated with the system IP address on the install
server.
For example, the Base Fabric interface is connected to the switch model-number in
slot 8 of the ATCA shelf. To install to this device, select the xxx Ethernet interface
from the BIOS setup menus.
# tip -9600 /dev/ttya
TABLE 2-2 Netinstall Boot Device Table
MAC Address Solaris
Device
Hardware
Device Connects to...
Switch Slot
Connection
0:3:ba.xx.xx.xn+0 /jointfilesconvert/526674/bge0 (BMC5715C) Base Fabric 0 Slot 7
0:3:ba.xx.xx.xn+1 /jointfilesconvert/526674/bge1 (BMC5715C) Base Fabric 1 Slot 8
0:3:ba.xx.xx.xn+2 nge0 (MCP55) mgtA (front panel)
0:3:ba.xx.xx.xn+3 nge1 (MCP55) mgtB (rear panel)
0:3:ba.xx.xx.xn+4 nxge0 (Sun 10 GbE
Multithreaded
Networking ASIC 10
GB)
Extended Fabric 0 Slot 7
- Sun Netra 1
- CP3220 Blade Server 1
- User’s Guide 1
- Contents 3
- ▼ To Install an ARTM 10 4
- Contents v 5
- ▼ Viewing OOS LED Settings 34 5
- ▼ Setting OOS LED Behavior 35 5
- Contents vii 7
- Figures xi 11
- Using UNIX Commands 16
- Shell Prompts 16
- Typographic Conventions 17
- Related Documentation 17
- Third-Party Web Sites 18
- Sun Welcomes Your Comments 18
- Introduction 19
- 1.1 Overview 20
- 1.2 Features 20
- 1.3 Physical Description 21
- Figure Leg end 22
- Chapter 1 Introduction 1-5 23
- 1.3.2 Blade Server Diagram 24
- 1.4 System Configurations 25
- FIGURE 1-6) 26
- Chapter 1 Introduction 1-9 27
- TABLE 1-1. Sun 28
- I/O Configurations 29
- 1.5 Hot-Swap Support 30
- 1.6 System Components 30
- 1.6.3 Software Components 31
- Information 32
- Chapter 1 Introduction 1-15 33
- ■ A ground mat 36
- Requirements 38
- ▼ To Install an ARTM 44
- FIGURE 2-2) 46
- The tip utility 48
- The minicom utility 48
- Solaris OS 49
- 2.3 Service Procedures 51
- 2.3.4 Powering On the System 52
- 2.3.6 Servicing DIMMs 53
- FIGURE 2-4 for DIMM 55
- FIGURE 2-5) 55
- 2.3.6.3 Removing a DDR2 DIMM 56
- Removing a DIMM 57
- FIGURE 2-7) 58
- Compact Flash Location 59
- FIGURE 2-8 60
- Removing an AMC Filler Panel 61
- Installing an AMC Card 62
- Pin Number Purpose 64
- ▼ Viewing OOS LED Settings 68
- ▼ Setting OOS LED Behavior 69
- Reset button 70
- Software Configuration 71
- 3.1 Operating Systems 72
- 3.2 Software Updates 72
- 3.3 SunVTS Software 73
- Behavior 75
- Data Bytes 76
- Configuring and Using BIOS 79
- Firmware 79
- 4.1 About BIOS Settings 80
- BIOS Setup Screens Summary 81
- Menu Item 82
- Setup Screens 83
- FIGURE 4-4) 87
- Change Password Menu 88
- FIGURE 4-5) 89
- 4.7 Updating the BIOS 90
- 4.8 Secondary BIOS Image 90
- 4.11 Power-On Self-Test 92
- 4.12 Changing POST Options 92
- POST Options 93
- Hardware Architecture 95
- 5.1 Block Diagram 96
- 5.2 The AMD Opteron Processor 97
- 5.3 Memory 98
- 5.4 Networking and I/O 99
- 5.4.2 PCI Express Bus 100
- 5.4.3 Dual BIOS 100
- 5.5 I/O Components 101
- 5.5.3 SAS/SATA 102
- Physical Characteristics 103
- A.2 Power and Thermal Metrics 104
- A.1 Form Factor 104
- Airflow Requirements 105
- ARTM Pressure Drop 105
- A.3 Connectors and Pinouts 106
- A.3.1.2 USB Ports 107
- A.3.2 AMC Connectors 108
- Pin Number Name Description 109
- Zone 2 Connector 111
- (Zone 3) 112
- J31 Connector Pin Assignments 113
- J32 Connector Pin Assignments 114
- J33 Connector Pin Assignments 114
- BIOS Screens 115
- FIGURE B-1 BIOS Menu Tree 116
- BIOS Main Menu 117
- Advanced Configuration Menu 117
- CPU Configuration Menu 118
- IDE Configuration Menu 118
- Super IO Configuration Menu 119
- ACPI Settings Menu 119
- Event Logging Details Menu 120
- MPS Configuration Menu 120
- SMBIOS Configuration Menu 121
- USB Configuration Menu 122
- Appendix B BIOS Screens B-9 123
- Boot Settings Menu 124
- Boot Device Priority Menu 125
- Security Settings Menu 126
- Change Password Settings Menu 126
- Chipset Main Menu 127
- Appendix B BIOS Screens B-15 129
- Exit Options Menu 130
- Appendix B BIOS Screens B-17 131
Relacionado con productos y manuales para Servidores Sun Microsystems CP3220
(60 paginas)
(68 paginas)Ika MS 3 digital Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Ausrüstung Ika MS 3 digital.
Wir stellen 2 PDF-Handbücher Ika MS 3 digital zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentarios a estos manuales