Sun-microsystems Gigabit Ethernet MMF/UTP Adapter Manual de usuario Pagina 75
- Pagina / 122
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 3 Configuring ipge and e1000 Driver Parameters 41
▼ To Configure Jumbo Frames Using ndd
1. Shut down and unplumb the interface.
2. Set the instance number:
In this example, the instance number set is 0.
3. Set the instance to accept Jumbo Frames:
4. Plumb the interface up:
where
xx.xx.xx.xx is the IP address of the interface.
▼ To Configure Jumbo Frames in a Linux
Environment
1. Ensure that the e1000 software is installed.
2. Plumb the Sun PCI-Express Dual Gigabit Ethernet interface:
where
xxx.xxx.xx.xxx is the IP address of the interface.
3. Set the MTU for maximum performance:
% ndd -set /dev/ipge instance 0
% ndd -set /dev/ipge accept-jumbo 1
% ifconfig ipge0 plumb xx.xx.xx.xx up
# modprobe e1000
# ifconfig eth2 xxx.xxx.xx.xxx up
# ifconfig eth2 mtu 8170
- PCI-Express Dual Gigabit 1
- Ethernet MMF/UTP Adapter 1
- Installation and User’s Guide 1
- Contents 3
- Index 87 7
- FCC Class B Notice 9
- FCC Class A Notice 9
- BSMI Class A Notice 11
- CCC Class A Notice 11
- GOST-R Certification Mark 12
- Safety Agency Compliance 13
- Statement 13
- Battery Warning 14
- System Unit Cover 14
- Rack System Warning 14
- Laser Compliance Notice 15
- CD and DVD Devices 15
- Mesures de sécurité 15
- Symboles 16
- Modification du matériel 16
- Conformité SELV 16
- Couvercle de l'unité 17
- Vorschriften 18
- Aufstellung von Sun-Geräten 19
- SELV-Konformität 19
- Anschluss des Netzkabels 19
- Warnung bezüglich Batterien 19
- Normativas de seguridad 20
- Class 1 Laser Product 23
- Luokan 1 Laserlaite 23
- Klasse 1 Laser Apparat 23
- Laser Klasse 1 23
- Declaration of Conformity 25
- Using UNIX Commands 30
- Typographic Conventions 31
- Shell Prompts 31
- Related Documentation 32
- Third-Party Web Sites 32
- Sun Welcomes Your Comments 33
- Sun PCI-Express Dual Gigabit 35
- Ethernet Adapter Overview 35
- Low-Profile Adapter 36
- ExpressModule Adapter 39
- ATNSW Attention Switch is a 41
- Patches and Updates 43
- Installing the Adapter 47
- To Verify the Installation 48
- Fiber pcs 51
- Copper mif 51
- Rebooting the System 52
- Power Off 52
- Hot-Plug 52
- Configuring ipge and e1000 55
- Driver Parameters 55
- ■ 100 Mbit/sec, half-duplex 56
- ■ 10 Mbit/sec, full-duplex 56
- ■ 10 Mbit/sec, half-duplex 56
- ■ Using the ndd utility 56
- ■ Using the ipge.conf file 56
- ■ Noninteractive 57
- ■ Interactive 57
- TABLE 3-4 through TABLE 3-1) 58
- % man prtconf 60
- ■ In this example: 61
- Link Partner Parameters 62
- To Discover Link Settings 64
- Checking Configurations 64
- # kstat ipge:0 65
- Driver Operating Statistics 66
- Parameter Description 67
- Device Driver Parameters 68
- Parameter Status Description 69
- Operational Mode Parameters 70
- Flow Control Parameters 71
- Interpacket Gap Parameters 72
- Interrupt Parameters 74
- Jumbo Frames 74
- Configuring e1000g Driver 77
- Parameters 77
- 1 10 Mpbs half-duplex 81
- 2 10Mpbs full-duplex 81
- 3 100Mpbs half-duplex 81
- 4 100Mpbs full-duplex 81
- Type the kstat command: 82
- 1500 but not 9000 90
- Configuring VLANs 91
- To Configure Static VLANs 94
- Operating range Up 100 meters 98
- Gigabit Ethernet UTP adapter 99
- ExpressModule Performance 100
- Specifications 100
- ExpressModule Environmental 101
- Requirements 101
- Specification Measurement 102
- Diagnostic Software 103
- SunVTS Documentation 104
- Using the SunVTS netlbtest 105
- ■ 10 Mbps PHY loopback 108
- Linux Platforms 111
- # depmod 112
- # modprobe e1000 112
- Low-Profile adapter 115
- Environment 116
- Keyword Description 118
- Interfaces 120
Relacionado con productos y manuales para Hardware Sun-microsystems Gigabit Ethernet MMF/UTP Adapter
(78 paginas)Ika MS 3 digital Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Ausrüstung Ika MS 3 digital.
Wir stellen 2 PDF-Handbücher Ika MS 3 digital zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentarios a estos manuales